PPPoE_Instal-Config
Interface da Internet WAN = eth0, no nosso caso, o ifcfg-eth0 deverá estar configurado para cliente dhcp.
# vim ifcfg-eth0
# Networking Interface
DEVICE=eth0
HWADDR=00:12:3f:fd:54:24
ONBOOT=yes
TYPE=Ethernet
BOOTPROTO=dhcp
Verificar
rpm -qa |
rpm -qa |
rpm -qa |
Instalando
# rpm –ivh
# rpm –ivh
# rpm –ivh
se os pacotes estão instalados:
grep rp-pppoe.i686
grep ppp-2.4
grep openssh
Pacotes Manualmente:
rp-pppoe-3.10-6.fc12.i686.rpm
ppp-2.4.5-9.fc13.i686.rpm
openssh-5.4p1-5.fc13.i686.rpm
Para remover o pacote o arquivo editado será mantido. # rpm –e <nome_pacote>
Instalando Automaticamente via Internet: # yum install rp-pppoe.i686
Configurando o rp-pppoe:
# pppoe-setup
# ------------------------------------------------------------------------------------------------------------ #
Welcome to the PPPoE client setup. First, I will run some checks on your system to make sure the PPPoE client
is installed properly...
The following DSL config was found on your system:
Device: Name: ppp0 DSLppp0
Please enter the device if you want to configure the present DSL config (default ppp0) or enter 'n' if you want
to
create a new one:
### <ENTER>
LOGIN NAME
Enter your Login Name (default [email protected] Este endereço de e-mail está protegido contra
spambots. Você deve habilitar o JavaScript para visualizá-lo. ):
### Informe seu usuário que é pago, ou se for o caso utilize o usuário de conexão do speedy. Usuário:
[email protected] Este endereço de e-mail está protegido contra spambots.
Você deve habilitar o JavaScript para visualizá-lo.
Senha: internet
### <ENTER>
INTERFACE
Enter the Ethernet interface connected to the PPPoE modem For Solaris, this is likely to be something like
/dev/hme0.
For Linux, it will be ethX, where 'X' is a number. (default eth0):
### <ENTER>
Do you want the link to come up on demand, or stay up continuously? If you want it to come up on demand,
enter the idle time in seconds after which the link should be dropped. If you want the link to stay up
permanently, enter 'no' (two letters, lower-case.) NOTE: Demand-activated links do not interact well with
dynamic IP addresses. You may have some problems with demand-activated links.
Enter the demand value (default no):
### <ENTER>
DNS
Please enter the IP address of your ISP's primary DNS server. If your ISP claims that 'the server will provide
dynamic DNS addresses', enter 'server' (all lower-case) here. If you just press enter, I will assume you know
what you are doing and not modify your DNS setup.
Enter the DNS information here:
### Apenas de <ENTER>
PASSWORD
Please enter your Password:
### Coloquei a minha senha ou coloca aquele senha internet
### internet <ENTER>
USERCTRL
Please enter 'yes' (three letters, lower-case.) if you want to allow normal user to start or stop DSL connection
(default yes):
### <ENTER> porque assim você permitirá que qualquer usuário faça um start se cair a rede.
Nova Era Informática
Quarta-feira, 7 de Dezembro de 2011 10:16 - Pág. 1 de 2.
PPPoE_Instal-Config
FIREWALLING
Please choose the firewall rules to use. Note that these rules are very basic. You are strongly encouraged to
use a more sophisticated firewall setup; however, these will provide basic security. If you are running any
servers on your machine, you must choose 'NONE' and set up firewalling yourself. Otherwise, the firewall rules
will deny access to all standard servers like Web, e-mail, ftp, etc. If you are using SSH, the rules will block
outgoing SSH connections which allocate a privileged source port.
The firewall choices are:
0 - NONE: This script will not set any firewall rules. You are responsible for ensuring the security of your
machine. You are STRONGLY recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway for a LAN
Choose a type of firewall (0-2): 0
### 2 <ENTER>
Start this connection at boot time Do you want to start this connection at boot time?
Please enter no or yes (default no): Se “yes” ao iniciar o pc inicia o pppoe automaticamente
### yes <ENTER>
** Summary of what you entered **
Ethernet Interface: eth0
User name: [email protected]
Activate-on-demand: No
DNS: Do not adjust
Firewalling: NONE
User Control: yes
Accept these settings and adjust configuration files (y/n)?
### y <ENTER>
Se você precisar depois alterar algo faça, pppoe-setup
Inseirir os DNS no Arquivo /etc/resolv.conf
nameserver 200.204.0.10
nameserver 200.204.0.138
Nova Era Informática
Quarta-feira, 7 de Dezembro de 2011 10:16 - Pág. 2 de 2.